Power Quality and Drives LLC search:

Home Motor Overload Protection Variable Frequency Drives Type 1 Enclosure Variable Frequency Drives with MCP Disconnect Type 1 Enclosure UL Type 1 Enclosed NEMA Rated Starters with No Pushbuttons ON and OFF Pushbuttons Combination Start, Stop HOA and CPT Combination HOA UL Type 4/12 Enclosed NEMA Rated Starters Start and Stop Pushbuttons Combination Start, Stop HOA and CPT Combination HOA Reversing Combination Reversing Explosionproof Control Non-Combination Starters Explosionproof Control Combination Starters Hazardous Location Switches Explosionproof Oher Equipment Starters Open Reversing Open Enclosures Solid State Reduced Voltage Contactors Solid State Contactors Pressure Transducers Lightning/Surge Suppressors Pump Control Simplex Duplex Manual or Automatic Alternation 1 Float Switch Control Non-combination Duplex Manual or Automatic Alternation 1 Float Switch Control Combination Duplex Manual or Automatic Alternation 1 or 2 Float Switch Control Non-combination Duplex Lead/Lag 3, 4, or 5 Float Switch Control Non-combination Duplex Lead/Lag 3, 4, or 5 Float Switch Control Combination Variable Frequency Drive Pump Packages Single and Three Phase Type 3R Enclosure All Products Listed If you don't see it . . . Store Policies Contact Us Start, Stop, Run Speed by Keypad Operation Copyright © 2008 Francis J. Martino Parameter / Set Keypad Display to read Notes DRV-03 / Keypad Press FWD, REV, STOP/RESET Keys on Keypad to Start, Stop Drive DRV-04 / Keypad-1 DRV-00 / 0.00 to 60.00 Hz Desired Frequency of operation Press PROG Button, Set the desired frequency, Press ENTER key. Output Frequency will change when ENTER key is pressed. OR DRV-04 / Keypad-2 DRV-00 / 0.00 to 60.00 Hz Desired Frequency of operation Press PROG Button, Press Up Arrow to increase speed, speed increases immediately. Press Down Arrow to decrease speed, speed decreases immediately. When desired speed is reached, press ENTER to write new value into memory. FU-1 / Run prev. /None Forward and Reverse keys are enabled /Forward Prev Forward run key is disabled /Reverse Prev Reverse run key is disabled The following Parameter settings are for all "common" applications. Factory default settings may be changed as necessary. Parameter / Set Keypad Display to read Notes DRV-00 / Cmd. Freq/Out Curr Program: Command (Run) Frequency when in PROG mode. Read Only: Command Frequency when in STOP Read Only: Output Frequency/Output Current during Run DRV-01 / Acc. time Factory Default: 20.0 sec DRV-02 / Dec. time Factory Default: 30.0 sec DRV-12 / Fault Code Read only. Fault codes are given in the Instruction Manual FU1-29 / Line Frequency Factory Default: 60.00 Hz FU1-30 / Maximum Frequency Factory Default: 60.00 Hz FU1-31 / Base Frequency Factory Default: 60.00 Hz FU1-32 / Start Frequency Factory Default: 0.50 Hz FU1-49 / VAC 440V Factory Default: 100.0% Set at 104.5% for 460 VAC at the motor terminals Set at 109.1% for 480 VAC at the motor terminals FU1-50 / Motor Volt 0 V Factory Default: 0.00 Set at motor nameplate rating: 200, 230 or 460. FU2-40 to FU2-45 / Motor HP, Poles, Slip, FLA Current, No-load Current, Efficiency FU2-46 / Load Inertia Set at 0 for load inertia less than 10 times that of motor inertia Set at 1 for load inertia at about 10 times that of motor inertia

Power Quality and Drives LLC P.O. Box 83 7 Yale Avenue Middlebury, CT  06762 USA Phone: (203) 217-2353 © Copyright 2010 - Power Quality and Drives LLC Privacy Policy