Power Quality and Drives LLC search:

Home Contactors Motor Overload Protection Inverter Duty Motors Variable Frequency Drives Type 1 Enclosure Variable Frequency Drives with Built-in EMC Filter and DC Reactor Type 1 and Type 12 Enclosures Variable Frequency Drives with MCP Disconnect Type 1 Enclosure UL Type 1 Enclosed NEMA Rated Starters with No Pushbuttons ON and OFF Pushbuttons Combination Start, Stop HOA and CPT Combination HOA UL Type 4/12 Enclosed NEMA Rated Starters Start and Stop Pushbuttons Combination Start, Stop HOA and CPT Combination HOA Reversing Combination Reversing Explosionproof Control Non-Combination Starters Explosionproof Control Combination Starters Explosionproof Combination with Ground Fault Hazardous Location Switches Explosionproof Oher Equipment Starters Open Reversing Starters Open Enclosures Solid State Reduced Voltage Contactors Reversing Contactors Solid State Contactors Pressure Transducers Lightning/Surge Suppressors Pump Control Simplex Duplex Manual or Automatic Alternation 1 Float Switch Control Non-combination Duplex Manual or Automatic Alternation 1 Float Switch Control Combination Duplex Manual or Automatic Alternation 1 or 2 Float Switch Control Non-combination Duplex Lead/Lag 3, 4, or 5 Float Switch Control Non-combination Duplex Lead/Lag 3, 4, or 5 Float Switch Control Combination Variable Frequency Drive Pump Packages Single and Three Phase Type 3R Enclosure All Products Listed If you don't see it . . . Store Policies Contact Us Constant Pressure with PID Control and Pressure Signal from 4-20 mA Pressure Transducer Start, Stop, by remote Pressure Switch Set-point by Keypad Operation Application: Vertical Turbine Pump Copyright © 2008 Francis J. Martino Parameter / Set Keypad Display to read Notes APP-02 Proc PI mode / Yes APP-04 Aux Ref Mode / No APP-06 PID F/B / I APP-07 PID P-gain / 1.0 % APP-08 PID I-time / 5.0 sec APP-10 PID limit-H / 60.00 Hz APP-11 PID limit-L / 45.00 Hz DRV-00 Command Frequency / Set Point (Hz) Set Point when using PID DRV-01 Acc. time / 5.0 sec DRV-02 Dec. time / 10.0 sec DRV-03 Fx/Rx-1 / 1 DRV-04 Freq Mode / Keypad-2 DRV-09 Motor Speed Reads speed in RPM FU1-01 Run Prev / Reverse Prevent FU1-23 Stop mode/ Decel FU1-33 Freq limit / No FU1-49 VAC AC Input Voltage / 104.5 % @ 230 VAC Program for voltage measured at Drive input terminals FU2-20 Power-on run / Yes Automatic restart upon restoration of power FU2-22 Speed Search / 1110 FU2-25 Retry number / 10 10 Auto-retries FU2-26 Retry delay / 60 sec Delay between retries. FU2-41 Pole number / 4 1800 RPM FU2-42 Rated-Curr / Motor FLA Set in service factor range if there is nuisance tripping FU2-61 Auto tuning / Yes I/O-26 M7 define / FX Terminal M7 will accept external contact connection to Terminal CM to provide Drive Start in Forward. Customer supplied Pressure Switch will provide contact closure between terminals M7 and CM. 60 lbs will start, 80 lbs will stop. Keypad Stop button is Disabled by I/O 26 M7 define. Separate operator station with push-pull START/STOP button must be added in series with the pressure switch contact to start and stop the Drive manually. Special Feature for the application: I/O-76 Run / A1 - C1 Inverter Run Detection gives a closed contact at output terminals A1 - C1. For use with Customer supplied chlorinator. FU2-95 Parameter Save

Power Quality and Drives LLC P.O. Box 83 7 Yale Avenue Middlebury, CT  06762 USA Phone: (203) 217-2353 © Copyright 2011 - Power Quality and Drives LLC Privacy Policy